Metal barn: do-it-yourself work
A barn is necessary for a private property in the city and village. You can’t do without it at the dacha. More and more tools, equipment, budmaterials are gradually accumulating, as it is necessary to save here. Nadiyne ukrittya for all these speeches - metal barn. Just remember - you don’t care about doing yoga on your own. Vіn go out for a vartistyu approximately equal to a wooden one, and richly cheap for a glance.
Technologies of everyday life of a barn
Є metal sheds are capital, and є zbіrnі. The capital shed from the hall can be a concrete foundation, as it is poured onto a prepared base, or it can be a tree. It is planned to use a paddle with planks, an upper strapping, on which the veins will spiral, fight with a profiled wall pipe with a 60 * 60 mm or 60 * 40 mm or a little piece with a torso wall 4-5 mm and more. Before the binding, the lags of the pidlogs are attached. The stench can be metal-like, or wood-like.
In a small shed with metal, it is possible to grow and subdue without a lag. For this binding, it is possible to sprout with a cloak of close 4-6 mm and a side of not less than 10 cm. Only a doshka can be but not less than 40 mm zavtovshki. At times of the great stretch, you may need additional support. Її it will be possible to work from a profile pipe with a double cut.
Selected/selected metal barn is built up from the well-built carcasses of the walls, which are bolted together. Sheathing is the most profiled sheet, as it is quickly installed and installed. From the same material, it was crushed and yes. You can install such a dispute at the dacha in a couple of years and dismantle it. Set an hour for the season in dachas that are not protected, and then either hove a castle, or take them to winter quarters.
There is one more variant of the choice shed (they are also called “state block”) - for those who do not want to worry about preparations. Industry prepares ready-made kits, which are chosen as a designer. Є variant of Chinese production, є vіtchiznyani. The price difference is not catastrophic 20-30%. And what you trust more, you rob. The storage of one of the Russian open air sheds is shown in the video.
Do-it-yourself metal shed from a professional sheet: photo
They used pipes of various cuts and corrugated boards, with a single dah. Rozmіri shed - 6.5 * 4 meters, the height of the front wall is 2.5 m, the back - 2.15 m.
Materials
Stands from round pipes with a diameter of 61 mm. They took them away, because they were from the state. Strapping and interstitial struts with pipes of straight cut - profiled (60-40 mm and 40 * 20 mm). Tovshchina of a wall skrіz – 2 mm.
Vitrata on pipes: round 32 m, profile large cut - 21 m, smaller - 156 m. 2.15 m-code, 16 arches 2.5 meters each. This is the list of materials for the frame. And also fixing and fittings for concrete:
- 16 bags of cement;
- 7 tons of gravel;
- waterproofing (1 roll);
- self-tapping screws, rivets, electrodes for welding;
- Wooden slats for grating: 50 * 25 mm - 3 pcs. 6 meters each.
Great list of budmaterials. But for the price, such a shed is still cheaper for looking at.
Pokrokov life
The cob is robit - the rose of the delyanka. Kіlochki are driven in at the corners, the diagonals are twisted. As if the stench is equal, the twine is stretched, according to the new, the places of the installation of the stands are moving. At designated places, mines are brown-coloured with a depth of 60 cm. Pipes are installed and filled with concrete (M200).
They put the bud on and poured the st_yki on the kutah. If the concrete was crumbling, the hairs were tied up to them - uphill at the bottom. Others were jealous of them.
The next stage is the construction of the frame. At the top of the pipes, a pipe 60 * 40 mm is welded from a 2 mm thick wall. Dali on one of the chimneys at the kutakhs, it is significant that the rіven pіdlogi. For help, we can tolerate yoga on other kutovі stіyki. Twine is attached to these vіdmіtkah and can be transferred to all stіyki. Weld along the perimeter of a pipe 40*20 mm. Following the same principle, we weld the cross-sections in the middle: two are definitely needed. Schob freely in the door of a walk-behind tractor or a wheelbarrow, the stench is crushed wide and high - 1.2 * 2 meters. The basis of the barn with metal with your own hands was already chosen.
Dali ide folding direct for covering. We needed three farmhouses 6.5 meters. They were welded on the ground, then they were welded to the beams. After that, we welded cross-cut pipes 40 * 20 mm (10 pieces). The frame of the metal shed is ready again. The next stage - priming - not rusty.
Dali rozpochali prepared concrete pіdlogi. The formwork was installed on the back. They put up a frame outside the boundaries, stepping up 10 cm. Dali carried out the preparation of the foundation. Rubble was driven into the ground and a bit of a ceglu. They beat him literally - with a gum mallet. Shmatok tsegli put on the ground, knocked, the docks of the wine may not be able to shove. The goal is to build a thick foundation, and even more uneven surfaces are more likely to be covered with soil.
After that, beacons were set up on a thick line - even slats (doska 25 * 50 mm), they were leveled along the hair: they marked specks on the opposite ends of the lower strapping and pulled the hair between them. Having pereverivshi її horizontality, beacons-slats were placed with it.
After that, as the rozchins on the lighthouses gathered, they poured concrete M-250 (). Rіvnyali rule vystavlenyh beacons and pipes of the lower piping, yakі hung on the same level.
Dali rozpochavsya installation of sheathing - profiled sheet. We started from the top. In order for the condensate to settle on the metal, without dripping on the head, a waterproofing pad was spread on the frame. They are laid with an overlap of one panel on the other side by about 10 centimeters, gluing them together with a special double-sided adhesive tape (sold there, de and waterproofing). It’s better not to vikoristovuvat Zvichaynu polietilenovu plіvka: it won’t be better to serve for a sprat of rokіv - a maximum of -3-5.
Start laying waterproofing from the bottom, sticking up the hill, gluing the panels together. So go out, like a drop, like a beast has fallen, flowing down to the very bottom. The smugs hung lower, lower, and hung down along the edges of the trochs (30 cm each) - so that water dripped from them and did not drain the small gaps of snow in the side wind.
Dali rozpochavsya installation of profiled sheet. When laying any sheet material on the ground, it is important to correctly place the first sheet. Then everything was given easily. To this, it is relativly visible to all the steps with squints, thin lines. If the sheet is set, yogo is screwed with screws. Їx to put at the hvilu - at the whistle. So there are less chances to drink water in the open.
With the sheathing of the sides, everything is approximately the same, only to be brought through the skins of the upper leaves to pinch. The first one installs evenly, they gave everything like clockwork. A new leaf equals the sickness and grows stronger. About 20 self-tapping screws were used to fasten one profiled sheet.
The frame of the doors is made of tієї and profile pipes 40*20 mm, welded loops. When sheathing the doors, they took it out and sewn it on a flat surface, hanging already at the finished look.
The metal barn was sheathed with a metal shed along the huts. Vіn landings on rivets. Serve for decoration, but also close the small gaps, as if they were set up with sticks on the ridges.
Vijshla more nizh mistka sporud - 26 squares. Yogo can be twisted for saving inventory, budmaterials, removing part of the machine. Tse yakscho vin to stand at the dealership of a booth.
For a dacha without protection, a shed made of metal - on the right is rizikovana, hut to sheathe the animal with a tree. Then you need to crepe wood paneling on the frame (pictured below).
We will be a flooded frame shed without filling: video
Not everything is possible, but open the hole and tighten the two elements with bolts more simply. On the video evidence, the whole process of folding a shed of decent rosemaries from a profile pipe on bolted connections. Zvaryuvannya vikoristano once: welded loops. There are no bolts here.
